HS code-based commodity chain analysis

List of the catalog of this article:

• 1,HS code-based commodity chain analysis National laws and regulations stipulate that the side of a seven-seater car must be sprayed?
• 2,What is the name of the side of the car hood
• 3. Is the side glass film of the car pasted inside or outside?
• 4, What is the name of the front side of the car
• 5, What is the name of the side of the plastic edge of the truck
• 6, How to repair the front wheel of the car if it hits the side and the wheel is crooked?

National laws and regulations stipulate that the side of a seven-seater car must be sprayed?

1. The side of a seven-seater car does not need to be sprayed. Legal basis: Technical Conditions for Motor Vehicle Operation Safety (GB7258-2012) GB7258-2012 Technical Conditions for Motor Vehicle Operation Safety 8 Article 8: All buses (except special school buses and buses) The number of passenger seats should be marked in an externally visible position near the door.

2. [Pacific Automobile Network] According to the provisions of the National Traffic Law, the operation of a 7-seater car must be sprayed on the body,Note that it is emphasized here that the operation of 7-seater vehicles, rather than the operation of private 7-seater vehicles, does not have the regulation of the Agricultural Bank of China card to be sprayed on the body.

3. For operating vehicles, it is necessary to spray words and spray the number of people. Private cars don't need to force words to spray.

4. The state does not have laws and regulations to stipulate that the side of a seven-seater car must be sprayed, but the "Technical Conditions for Motor Vehicle Operation Safety" stipulates the quality and types of different types of vehicles that should be sprayed.

What is the name of the side of the hood of the car

The metal guard connected to the bumper guard on both sides of the hood is called the front and lower guard.

Generally, there are four parts on the periphery of the front part of the vehicle, and the front is the front bumper. The two sides are the left leaf plate or the left side and the right leaf plate or also called the right side.

The names of each part of the car shell are: hood, left wing sub-plate, left front door, left middle door, left plate, tailgate, right plate, right middle door, right front door, right wing sub-board, roof. Some cars do not have middle doors, such as sports cars.

In the automotive industry, the engine front cover is often called the "hood" because it plays a key role in the protection and maintenance of the car engine. In addition, in some automobile manufacturers, the engine front cover has other names, such as "engine hood", "engine hood", etc.

Car wing plate Car wing plate, also known as leaf plate, is located outside the body of the tire and can be regarded as a covering component. It can not only reduce the wind resistance when driving according to fluid mechanics, but also play a great role in the reliability of the car.

Is the side glass film of the car pasted inside or outside?

1. The car film should be attached to the inside of the car glass, because the inside will not be affected by wind and rain, and the aging will be slower, thus prolonging the service life; at the same time, the film will not be affected by too much externalInterference, it will not be broken by hanging and hitting, without experiencing wind and rain, the pasting will be firmer, and there will be no bumps and so on.

2. The car glass film is generally pasted inside: before applying the film, the necessary parts of the car must be covered to prevent liquid infiltration. The sprayed cleaning liquid and lubricant will affect the decorative parts such as on-board electronic equipment and in-car seats; the front of the film is in the window.

3. Stick it in the car. The front windshield film of the car is attached to the inside of the glass and also to the inside of the glass of the front windshield of the vehicle. The film of the glass at other positions of the vehicle, including the left and right windows, and the film of the rear windshield, is attached to the inside of the glass.

4. The car film sticker is inside the sticker. Generally speaking, the front and rear windshields and window films of cars are pasted onInside, long-term wind and sun exposure will cause non-staining, curling or functional degradation to the film, and the inside of the film will not be affected by the outside.

What is the name of the front side iron sheet

Yes, it's called wing plate. This is a piece of assembly, and a plastic plate on the inside is called a fender (trucks also use steel plates as fenders).

The name of all tin parts starting from the front bumper of a car. It's better to have a picture. For example: front bumper-front leaf plate-..

The iron sheet of the outer outline of the car on the left front wheel and the iron sheet connected to the fender inside are called the wing plate.

Steel plate stamping parts. According to the official website of Autohome, the iron sheet on the a-pillar of the car is called steel plate stamping.The part is a part of the body structure, covering the outside of the A-pillar, which plays a role in protecting the A-pillar and beautifying the body. It is often used to install airbags, wipers and other parts on the side of the car.

The front and rear railings of the truck with iron are called bumpers, which can play a protective role in the event of an accident.

What is the name of the side of the plastic edge of the truck

It's called the side skirt. The side skirt refers to the skirt plate installed on both sides of the car body, which is also equivalent to the air dam, which is used to reduce the airflow on both sides of the car body entering the bottom of the car. It has a certain disturbance effect, which can significantly reduce air resistance under certain conditions.

. Strip pattern. Advantages: large side slip resistance, excellent steering and safety performance, small vibration, comfortable driving experience.Disadvantages: Poor braking and driving performance, and grooves are prone to fatigue. It is mainly used in the steering wheel of the truck and the place where the road surface is relatively good. Horizontal pattern.

This is an anti-scratch strip, which means to prevent the damage to the vehicle and reduce the loss when there is a slight friction on both sides of the vehicle. The function of the leaf plate: The leaf plate can prevent the sand, stones and mud rolled up by the wheels from splashing to the bottom of the car during the driving process, and reduce the damage and corrosion to the chassis.

The iron bars on both sides under the rear door of the Mi2 truck are called side skirts. According to the relevant public information of the query, the effect of the side skirt is equivalent to an air dam, which is used to reduce the airflow from both sides of the car body into the bottom of the car. The side skirt is made of plastic material, which is easy to damage when scratched.

How to repair the front wheel of the car if it hits the side and the wheel is crooked?

To judge whether the car has a broken axle, you can drive the car to the car repair shop with a lifter, ask the car repairman to help find the position of the half-axle, clean up the dirt on the half-axle, and check whether there are small cracks or complete breaks on it.

First, check whether the tires are unevenly worn or damaged. If only one wheel is skewed, it can be corrected by changing the tire wheel. However, if there is a problem with multiple wheels, it may need to be balanced and adjusted.

The front wheel of the car is crooked. Generally, the shock absorber and bumper connecting shaft are deformed. At this time, do not continue to drive. You need to go to the repair shop for inspection and confirmation. Shock absorbers are mainly divided into hydraulic and inflatable from the perspective of the material that produces damping, and there is also a variable damping shock absorber.

The way to repair the crooked right front wheel of Passat is to change a new tire. Remove the bad tires. Choose a tire of good quality, strong and durable. Go to the car repair shop to replace it.