1. The solution that the U disk installation system cannot find the hard disk is to change the hard disk mode to IDE.
2. Change the hard disk mode to IDEU. If the hard disk installation system can't find the hard disk, the solution is to change the hard disk mode to IDE. The specific operation method is as follows: power-on---press F2 to enter the BIOS. After entering the BIOS, you can press the left and right up and down keys to adjust the options, and then select Adv Anced.
3. In SATA mode, the startup of the USB flash drive is restricted. Users can only use it normally by changing the SATA mode to IDE mode. The graphics and text of the hard disk cannot be found after the USB disk is installed.Tutorial http:// If the above methods cannot solve the problem, you can refer to this tutorial..
4. Enter BIOS, set Security-Secure Boot Control to Disabled, Boot-Launch CSM to Enabled, press F10 to save, insert the system installation USB flash drive, heavy Press ESC to select the startup item to reinstall the system. If the hard disk device cannot be recognized in the BIOS, it is recommended to send it to the service center for repair.
ghost software is generally used to back up and restore the system, and it is impossible to do this continuously. It is unlikely to do it once a day. , so it won't hurt the hard disk.
The installation of the GHOST system is to format the hard disk once, and then write the file to the hard disk at high speed. These operations are still a little harmful to the hard disk, but the damage is very small, just like daily operation formatting and writing files to the hard disk.
Therefore, if the quality of the memory stick is poor or the contact is not very good, it is easy to have a blue screen when reinstalling the system (including GHOST). This phenomenon is most likely to occur when the installation process is restarted.
Ghost installing the system is equivalent to copying and assembling all the system files once. The real physical operation is to write the file. The damage caused by file copying is similar, but the number of files is a little more when reinstalling. It won't hurt much to reinstall occasionally. Of course, it's not good to do this often.
If you restart the computer due to a sudden power outage or voltage fluctuation when backing up or restoring the system, it is easy to cause damage to the hard disk (sometimes it can be solved by repartitioning, but sometimes it may cause hard damage to the hard disk that cannot be repaired), so when using GHOST, Be careful.
1. We plug the pre-made USB disk boot disk into the computer, and press DEL to enter the BIOS to set it as a USB disk to start up. The USB disk boot menu will appear, and select "Run Cabbage WIN8PEx64 Enhanced Version".
2. Enter the BIOS interface, find the Boot option, and set the solid-state drive as the first boot item.Save the settings and exit, and the computer will restart automatically. Insert the installed USB flash drive or CD into the computer, restart the computer, and enter the installation interface. In the installation interface, select the solid-state drive for system installation.
3. Prepare the installation CD or USB boot disk, which contains the installation file of the operating system you want to install. Insert the installation CD or USB boot disk into the computer and restart the computer. Press the corresponding key (usually FF1Del, etc.) when the computer starts to enter the BIOS settings.
4. First of all, format the newly purchased solid-state drive in the computer system. It is best not to format quickly, but to format slowly. After formatting, install the system with the one-click restore tool. If there is no accident in the middle, you can be sure that there is no problem with the system installation.
5. Copy the iso image of the win10 system directly to the USB flash drive, and the micro-pe boot disk supports larger than 4G mirror images; insert the USB flash drive into the computer with ssd solid-state drive. In order to give full play to the speed of the solid-state disk, first enter the BIOS to turn on the hard disk AHCI mode, but the new computer The default is ahci, which does not need to be changed. This step can basically be omitted.
6. Note: Before operating, please make sure that your solid-state drive has been installed on the computer and plugged in the data cable and power cable.
1. The mobile hard disk can be used as a system as a main disk. Types of system disk: In terms of discs, the system disk is a CD-ROM with a boot installation system.In terms of hard disk, the system disk usually refers to the C disk, while the boot disk can only be a CD-ROM.
2. Yes, mobile solid-state drive is also a kind of solid-state drive, but a different connection method with the computer.
3. In general, the mobile hard disk installation system is of little significance in reality, because different computer hardware configurations require different drivers. If you have to install the system on the mobile hard disk, you can download boot disks such as cabbage from the Internet to install and use.
1. Enter the BIOS interface, find the Boot option, and set the solid-state drive as the first boot item. Save the settings and exit, and the computer will restart automatically.Insert the installed USB flash drive or CD into the computer, restart the computer, and enter the installation interface. In the installation interface, select the solid-state drive for system installation.
2. We plug the pre-made USB disk boot disk into the computer, press DEL to enter the BIOS and set the USB disk startup. At startup, the USB disk startup menu will appear, and select "Run Cabbage WIN8PEx64 Enhanced Version".
3. Prepare the installation CD or USB boot disk, which contains the installation file of the operating system you want to install. Insert the installation CD or USB boot disk into the computer and restart the computer. Press the corresponding key (usually FF1Del, etc.) when the computer starts to enter the BIOS settings.
1. Install the hard disk: Install the solid-state drive into the computer host. HARD DISK PARTITION: USE A USB FLASH DRIVE TO START THE COMPUTER AND RUN TOOLS SUCH AS DISKGENIUS TO PARTITION THE HARD DISK. ( 1) Make a boot USB flash drive: A. Go to the physical store to buy a branded USB flash drive with a capacity of 4 or 8G or more.
2. The first step is to install a solid-state drive into the computer.The second step is to open the BIOS mode in the computer, and then adjust the order of the solid-state drive to the front of the original mechanical hard disk in the boot order. The third step is to enter the installation of the system.
3. Install the system Step 1 Preparations have finally entered the installer.
Global trade analysis dashboard-APP, download it now, new users will receive a novice gift pack.
1. The solution that the U disk installation system cannot find the hard disk is to change the hard disk mode to IDE.
2. Change the hard disk mode to IDEU. If the hard disk installation system can't find the hard disk, the solution is to change the hard disk mode to IDE. The specific operation method is as follows: power-on---press F2 to enter the BIOS. After entering the BIOS, you can press the left and right up and down keys to adjust the options, and then select Adv Anced.
3. In SATA mode, the startup of the USB flash drive is restricted. Users can only use it normally by changing the SATA mode to IDE mode. The graphics and text of the hard disk cannot be found after the USB disk is installed.Tutorial http:// If the above methods cannot solve the problem, you can refer to this tutorial..
4. Enter BIOS, set Security-Secure Boot Control to Disabled, Boot-Launch CSM to Enabled, press F10 to save, insert the system installation USB flash drive, heavy Press ESC to select the startup item to reinstall the system. If the hard disk device cannot be recognized in the BIOS, it is recommended to send it to the service center for repair.
ghost software is generally used to back up and restore the system, and it is impossible to do this continuously. It is unlikely to do it once a day. , so it won't hurt the hard disk.
The installation of the GHOST system is to format the hard disk once, and then write the file to the hard disk at high speed. These operations are still a little harmful to the hard disk, but the damage is very small, just like daily operation formatting and writing files to the hard disk.
Therefore, if the quality of the memory stick is poor or the contact is not very good, it is easy to have a blue screen when reinstalling the system (including GHOST). This phenomenon is most likely to occur when the installation process is restarted.
Ghost installing the system is equivalent to copying and assembling all the system files once. The real physical operation is to write the file. The damage caused by file copying is similar, but the number of files is a little more when reinstalling. It won't hurt much to reinstall occasionally. Of course, it's not good to do this often.
If you restart the computer due to a sudden power outage or voltage fluctuation when backing up or restoring the system, it is easy to cause damage to the hard disk (sometimes it can be solved by repartitioning, but sometimes it may cause hard damage to the hard disk that cannot be repaired), so when using GHOST, Be careful.
1. We plug the pre-made USB disk boot disk into the computer, and press DEL to enter the BIOS to set it as a USB disk to start up. The USB disk boot menu will appear, and select "Run Cabbage WIN8PEx64 Enhanced Version".
2. Enter the BIOS interface, find the Boot option, and set the solid-state drive as the first boot item.Save the settings and exit, and the computer will restart automatically. Insert the installed USB flash drive or CD into the computer, restart the computer, and enter the installation interface. In the installation interface, select the solid-state drive for system installation.
3. Prepare the installation CD or USB boot disk, which contains the installation file of the operating system you want to install. Insert the installation CD or USB boot disk into the computer and restart the computer. Press the corresponding key (usually FF1Del, etc.) when the computer starts to enter the BIOS settings.
4. First of all, format the newly purchased solid-state drive in the computer system. It is best not to format quickly, but to format slowly. After formatting, install the system with the one-click restore tool. If there is no accident in the middle, you can be sure that there is no problem with the system installation.
5. Copy the iso image of the win10 system directly to the USB flash drive, and the micro-pe boot disk supports larger than 4G mirror images; insert the USB flash drive into the computer with ssd solid-state drive. In order to give full play to the speed of the solid-state disk, first enter the BIOS to turn on the hard disk AHCI mode, but the new computer The default is ahci, which does not need to be changed. This step can basically be omitted.
6. Note: Before operating, please make sure that your solid-state drive has been installed on the computer and plugged in the data cable and power cable.
1. The mobile hard disk can be used as a system as a main disk. Types of system disk: In terms of discs, the system disk is a CD-ROM with a boot installation system.In terms of hard disk, the system disk usually refers to the C disk, while the boot disk can only be a CD-ROM.
2. Yes, mobile solid-state drive is also a kind of solid-state drive, but a different connection method with the computer.
3. In general, the mobile hard disk installation system is of little significance in reality, because different computer hardware configurations require different drivers. If you have to install the system on the mobile hard disk, you can download boot disks such as cabbage from the Internet to install and use.
1. Enter the BIOS interface, find the Boot option, and set the solid-state drive as the first boot item. Save the settings and exit, and the computer will restart automatically.Insert the installed USB flash drive or CD into the computer, restart the computer, and enter the installation interface. In the installation interface, select the solid-state drive for system installation.
2. We plug the pre-made USB disk boot disk into the computer, press DEL to enter the BIOS and set the USB disk startup. At startup, the USB disk startup menu will appear, and select "Run Cabbage WIN8PEx64 Enhanced Version".
3. Prepare the installation CD or USB boot disk, which contains the installation file of the operating system you want to install. Insert the installation CD or USB boot disk into the computer and restart the computer. Press the corresponding key (usually FF1Del, etc.) when the computer starts to enter the BIOS settings.
1. Install the hard disk: Install the solid-state drive into the computer host. HARD DISK PARTITION: USE A USB FLASH DRIVE TO START THE COMPUTER AND RUN TOOLS SUCH AS DISKGENIUS TO PARTITION THE HARD DISK. ( 1) Make a boot USB flash drive: A. Go to the physical store to buy a branded USB flash drive with a capacity of 4 or 8G or more.
2. The first step is to install a solid-state drive into the computer.The second step is to open the BIOS mode in the computer, and then adjust the order of the solid-state drive to the front of the original mechanical hard disk in the boot order. The third step is to enter the installation of the system.
3. Install the system Step 1 Preparations have finally entered the installer.
Export quota monitoring software
author: 2024-12-23 22:20HS code alignment for halal imports
author: 2024-12-23 21:39How to mitigate currency fluctuation risk
author: 2024-12-23 21:27Cost-benefit analysis of export markets
author: 2024-12-23 20:44Advanced tariff classification tools
author: 2024-12-23 22:00Trade data for resource allocation
author: 2024-12-23 21:51Dynamic supplier inventory analysis
author: 2024-12-23 21:44Commodity-specific import licensing data
author: 2024-12-23 20:24624.47MB
Check332.79MB
Check294.41MB
Check775.59MB
Check272.56MB
Check994.95MB
Check477.25MB
Check675.99MB
Check225.19MB
Check738.98MB
Check878.21MB
Check745.12MB
Check256.93MB
Check529.98MB
Check541.12MB
Check172.87MB
Check735.61MB
Check447.39MB
Check644.69MB
Check443.64MB
Check411.89MB
Check869.35MB
Check575.31MB
Check183.61MB
Check798.38MB
Check335.96MB
Check337.88MB
Check873.95MB
Check565.88MB
Check463.46MB
Check718.58MB
Check449.85MB
Check664.34MB
Check514.38MB
Check892.47MB
Check499.14MB
CheckScan to install
Global trade analysis dashboard to discover more
Netizen comments More
2367 International trade knowledge base
2024-12-23 22:16 recommend
267 Exotic spices HS code classification
2024-12-23 21:59 recommend
2970 How to navigate non-tariff barriers
2024-12-23 21:17 recommend
603 global market access
2024-12-23 21:09 recommend
254 HS code-led regulatory frameworks
2024-12-23 20:14 recommend