1. If the width is too large, there will be no accident during overtaking or if the road marking is narrower than the width of the car, the state stipulates that the car The total width of the vehicle shall not exceed 5m to meet the needs of the use of relevant public roads.
2. However, as long as it meets the national standard "Dimensions, Axle Weight and Mass Limits of Road Vehicles" (GB1589-2004), they are all standard sizes.Measurement method of car size: length and number of times; width × height. As the name implies, the so-called length, width and height are the external dimensions of the car, usually in millimeters (mm).
3. Width is the distance between the most prominent points of the outer sheet metal of the body. The length data of a car is the distance from the front of the front to the end of the rear of the car. The width is the distance between the most prominent points of the outer sheet metal of the car body. Generally, the front wheel eyebrow position of the car is the widest, and the general reflector is not included in the width of the body.
4. According to the common rules in the industry, the width of the body does not include the width of the left and right rearview mirrors, that is, the width after the rearview mirror is folded. The height of the car body is defined as: the distance from the ground to the highest point of the car. The so-called highest point is the highest position on the top of the body, but does not include the length of the roof antenna.
5. Vehicle width: Vehicle width is the distance between the two planes parallel to the longitudinal symmetrical plane of the vehicle and facing the fixed protruding parts on both sides of the vehicle. The automatic measuring instrument of vehicle outline size should comply with the measurement regulations, and the maximum allowable error of the measuring instrument: 1% or 20mm.
6. The body size is the data of the length, width and height of the car, indicating the external size of the car body. Body length × width × height measurement standard: body length refers to the distance from the most prominent position at the front of the car to the most prominent position at the rear of the car.
Benchmarks In actual measurement work, the plane of the body corrector is generally taken as the height reference plane.
In the body knotIn structural maintenance, when measuring the body structure data with the body measurement system, there are three important dimensional reference benchmarks: reference surface, central surface and zero plane.
Therefore, the use of steel tape measure and gauge can meet the measurement requirements. When using the body data chart as the basis for measurement, vehicle parameter information such as model and production year should be correctly selected. Parameter comparison When selecting the measurement reference point, the following principles should usually be followed. 1 Confirm that the measurement reference point is not deformed.
The body width is defined as the distance between the two extreme points in the direction of the width of the car, that is, the distance between the most prominent positions on the left and right of the car body. According to the general rules of the industry, the body width does not include the extension width of the left and right rearview mirrors, that is, the width of the folding rearview mirrors. The body height is defined as the distance from the ground to the highest point of the car.
The quality of the whole vehicle equipment (kg): the quality of the car is fully equipped, including the quality of all equipment such as lubricating oil, fuel, accompanying tools, spare tires, etc. Maximum total mass (kg): the total mass when the car is fully loaded. Maximum loading mass (kg): the maximum loading mass when the car is driving on the road.
Therefore, the use of steel tape measure and gauge ruler can meet the measurement requirements. When using the body data chart as the basis for measurement, vehicle parameter information such as model and year of production should be correctly selected. ( 2) Parameter comparison: When comparing parameters, the following principles should generally be followed: ensure that the measurement reference point is not deformed.
1. Measurement of size: In the body structure, most control points are holes, and the measurement of size is to measure the center point to the center point. Generally, a track gauge is used for measurement.
2. You need a tape measure or laser rangefinder. If you choose to use a tape measure, make sure it is accurate and long enough to measure the length of the entire body. If you choose to use a laser rangefinder, follow the instructions to make sure that it has been calibrated and ready for use.
3. In order to accurately obtain the body data, the three steps are the measurement of the size, the measurement of the upper body size, and the measurement of the front size of the body. Measurement of size: In the body structure, most control points are holes, and the measurement of size is to measure the center point to the center point. Generally, a track gauge is used for measurement.
4. Measurement of the overall deformation of the car body: Body shaping positioning detection is to use the measurement system provided by the straightening system to measure the coordinate parameters of each measurement point on the body, and compare the measurement data with the standard data of the model to check the straightening quality.
5. Stop the car after driving 10km on the road with poor road conditions, and touch the shock absorber shell with your hand. If it is not hot enough, it means that there is no resistance inside the shock absorber and the shock absorber does not work.
The front bundle ruler can be used to check and measure the front bundle. The tested vehicle must ensure that the tire pressure, the wheel is not in the center, the steering mechanism and the wheel bearing adjustment are in good condition, and the front wheel must be in the center and straight. When measuring with a front ruler, park the car on a flat, dry and clean ground.
Measurement method of automobile front bundle: First of all, the measurement method of automobile wheel bearing clearance is adjusted, and the tire inflation pressure conforms to the regulations.
The adjustment and measurement of the front beam of the car are as follows: the front beam of the front wheel is to make the distance between the front end of the two front wheels of the car smaller than the distance of the rear end.The difference in distance is called the front beam value. Looking down from the top of the car, the left and right front wheels form an "eight" shape with an opening to the back; the front bundle of the front wheel can be adjusted by changing the length of the crossbar.
Checking the front bundle value is generally carried out on a special front wheel locator. The front beam measurement method is first of all to adjust the gap of the automobile wheel hub bearing, and the tire inflation pressure conforms to the regulations. Park the car on the horizontal road and drive in a straight line.
Therefore, when the current bundle value is inappropriate, it needs to be adjusted and measured. To measure the front beam of a car, it is generally necessary to use a special front wheel locator, and generally there is no such professional instrument for self-measurement, and it can only be measured through simple tools. Of course, there is a certain error in the front beam of the car measured in this way.
1. Car size detection is as follows: the body length is defined as the distance between the two extreme points of the car, that is, the distance between the two points from the most prominent position of the front bumper of the car to the most prominent position of the rear bumper.
2. Body size: First, we will measure the size of each part of the car body, including the length, width and height. These data are crucial to the design, manufacture and safety of vehicles. For example, if the body width exceeds the specified limit, the vehicle may not be able to drive on certain roads.
3. Measurement of size: In the body structure, most of the control points are holes, and the measurement of size is to measure the center point to the center point. Generally, a track gauge is used for measurement.
4. When the freight vehicle passes through the off-site law enforcement monitoring point normally at a running speed range of 0.5-100km/h, the Shenbang outline size measurement ADM system can automatically complete the identification and measurement of the length, width and height profile size and wheelbase of the freight vehicle, and output the correct measurement results to Off-site law enforcement edge management server.
Textile yarn HS code mapping-APP, download it now, new users will receive a novice gift pack.
1. If the width is too large, there will be no accident during overtaking or if the road marking is narrower than the width of the car, the state stipulates that the car The total width of the vehicle shall not exceed 5m to meet the needs of the use of relevant public roads.
2. However, as long as it meets the national standard "Dimensions, Axle Weight and Mass Limits of Road Vehicles" (GB1589-2004), they are all standard sizes.Measurement method of car size: length and number of times; width × height. As the name implies, the so-called length, width and height are the external dimensions of the car, usually in millimeters (mm).
3. Width is the distance between the most prominent points of the outer sheet metal of the body. The length data of a car is the distance from the front of the front to the end of the rear of the car. The width is the distance between the most prominent points of the outer sheet metal of the car body. Generally, the front wheel eyebrow position of the car is the widest, and the general reflector is not included in the width of the body.
4. According to the common rules in the industry, the width of the body does not include the width of the left and right rearview mirrors, that is, the width after the rearview mirror is folded. The height of the car body is defined as: the distance from the ground to the highest point of the car. The so-called highest point is the highest position on the top of the body, but does not include the length of the roof antenna.
5. Vehicle width: Vehicle width is the distance between the two planes parallel to the longitudinal symmetrical plane of the vehicle and facing the fixed protruding parts on both sides of the vehicle. The automatic measuring instrument of vehicle outline size should comply with the measurement regulations, and the maximum allowable error of the measuring instrument: 1% or 20mm.
6. The body size is the data of the length, width and height of the car, indicating the external size of the car body. Body length × width × height measurement standard: body length refers to the distance from the most prominent position at the front of the car to the most prominent position at the rear of the car.
Benchmarks In actual measurement work, the plane of the body corrector is generally taken as the height reference plane.
In the body knotIn structural maintenance, when measuring the body structure data with the body measurement system, there are three important dimensional reference benchmarks: reference surface, central surface and zero plane.
Therefore, the use of steel tape measure and gauge can meet the measurement requirements. When using the body data chart as the basis for measurement, vehicle parameter information such as model and production year should be correctly selected. Parameter comparison When selecting the measurement reference point, the following principles should usually be followed. 1 Confirm that the measurement reference point is not deformed.
The body width is defined as the distance between the two extreme points in the direction of the width of the car, that is, the distance between the most prominent positions on the left and right of the car body. According to the general rules of the industry, the body width does not include the extension width of the left and right rearview mirrors, that is, the width of the folding rearview mirrors. The body height is defined as the distance from the ground to the highest point of the car.
The quality of the whole vehicle equipment (kg): the quality of the car is fully equipped, including the quality of all equipment such as lubricating oil, fuel, accompanying tools, spare tires, etc. Maximum total mass (kg): the total mass when the car is fully loaded. Maximum loading mass (kg): the maximum loading mass when the car is driving on the road.
Therefore, the use of steel tape measure and gauge ruler can meet the measurement requirements. When using the body data chart as the basis for measurement, vehicle parameter information such as model and year of production should be correctly selected. ( 2) Parameter comparison: When comparing parameters, the following principles should generally be followed: ensure that the measurement reference point is not deformed.
1. Measurement of size: In the body structure, most control points are holes, and the measurement of size is to measure the center point to the center point. Generally, a track gauge is used for measurement.
2. You need a tape measure or laser rangefinder. If you choose to use a tape measure, make sure it is accurate and long enough to measure the length of the entire body. If you choose to use a laser rangefinder, follow the instructions to make sure that it has been calibrated and ready for use.
3. In order to accurately obtain the body data, the three steps are the measurement of the size, the measurement of the upper body size, and the measurement of the front size of the body. Measurement of size: In the body structure, most control points are holes, and the measurement of size is to measure the center point to the center point. Generally, a track gauge is used for measurement.
4. Measurement of the overall deformation of the car body: Body shaping positioning detection is to use the measurement system provided by the straightening system to measure the coordinate parameters of each measurement point on the body, and compare the measurement data with the standard data of the model to check the straightening quality.
5. Stop the car after driving 10km on the road with poor road conditions, and touch the shock absorber shell with your hand. If it is not hot enough, it means that there is no resistance inside the shock absorber and the shock absorber does not work.
The front bundle ruler can be used to check and measure the front bundle. The tested vehicle must ensure that the tire pressure, the wheel is not in the center, the steering mechanism and the wheel bearing adjustment are in good condition, and the front wheel must be in the center and straight. When measuring with a front ruler, park the car on a flat, dry and clean ground.
Measurement method of automobile front bundle: First of all, the measurement method of automobile wheel bearing clearance is adjusted, and the tire inflation pressure conforms to the regulations.
The adjustment and measurement of the front beam of the car are as follows: the front beam of the front wheel is to make the distance between the front end of the two front wheels of the car smaller than the distance of the rear end.The difference in distance is called the front beam value. Looking down from the top of the car, the left and right front wheels form an "eight" shape with an opening to the back; the front bundle of the front wheel can be adjusted by changing the length of the crossbar.
Checking the front bundle value is generally carried out on a special front wheel locator. The front beam measurement method is first of all to adjust the gap of the automobile wheel hub bearing, and the tire inflation pressure conforms to the regulations. Park the car on the horizontal road and drive in a straight line.
Therefore, when the current bundle value is inappropriate, it needs to be adjusted and measured. To measure the front beam of a car, it is generally necessary to use a special front wheel locator, and generally there is no such professional instrument for self-measurement, and it can only be measured through simple tools. Of course, there is a certain error in the front beam of the car measured in this way.
1. Car size detection is as follows: the body length is defined as the distance between the two extreme points of the car, that is, the distance between the two points from the most prominent position of the front bumper of the car to the most prominent position of the rear bumper.
2. Body size: First, we will measure the size of each part of the car body, including the length, width and height. These data are crucial to the design, manufacture and safety of vehicles. For example, if the body width exceeds the specified limit, the vehicle may not be able to drive on certain roads.
3. Measurement of size: In the body structure, most of the control points are holes, and the measurement of size is to measure the center point to the center point. Generally, a track gauge is used for measurement.
4. When the freight vehicle passes through the off-site law enforcement monitoring point normally at a running speed range of 0.5-100km/h, the Shenbang outline size measurement ADM system can automatically complete the identification and measurement of the length, width and height profile size and wheelbase of the freight vehicle, and output the correct measurement results to Off-site law enforcement edge management server.
Comparing duty rates across markets
author: 2024-12-24 02:35International trade compliance workflow
author: 2024-12-24 02:13HS code applications in compliance software
author: 2024-12-24 01:30Global trade documentation standards
author: 2024-12-24 00:24Global HS code classification standards
author: 2024-12-24 02:27Analytical tools for trade diversification
author: 2024-12-24 02:20Industry-specific trade data filters
author: 2024-12-24 00:31How to interpret trade statistics
author: 2024-12-24 00:02
HS code utilization for tariff refunds
583.46MB
Check
HS code-driven route selection
414.53MB
Check
HS code alignment for halal imports
258.67MB
Check
How to enhance supplier collaboration
963.88MB
Check
Automated customs declaration checks
894.75MB
Check
How to use trade data for market expansion
412.51MB
Check
Real-time trade data feeds
987.83MB
Check
How to detect trade-based money laundering
882.25MB
Check
Customs authorization via HS code checks
374.53MB
Check
HS code filters for bulk commodities
829.86MB
Check
How to leverage trade data in negotiations
488.89MB
Check
How to integrate AI in trade data analysis
373.99MB
Check
Identifying duty exemptions via HS code
837.37MB
Check
Trade data solutions for wholesalers
597.63MB
Check
How to comply with EU trade regulations
676.95MB
Check
HS code-based competitive advantage analysis
194.72MB
Check
HS code-driven risk management frameworks
922.94MB
Check
HS code tagging in tariff databases
947.25MB
Check
Industrial equipment HS code alignment
155.38MB
Check
HS code-based container stowage planning
695.15MB
Check
Pharma cold chain HS code analysis
719.28MB
Check
Global trade lead generation tools
194.81MB
Check
HS code analytics for niche markets
317.56MB
Check
Global trade resource libraries
638.65MB
Check
Global trade certificate verification
444.46MB
Check
Trade data for strategic sourcing
577.91MB
Check
HS code lookup for Asia-Pacific markets
951.63MB
Check
HS code-driven risk management frameworks
558.44MB
Check
Industry consolidation via HS code data
135.24MB
Check
Australia HS code tariff insights
578.75MB
Check
Enhanced supplier vetting processes
537.71MB
Check
Real-time customs clearance alerts
291.11MB
Check
Global trade credit risk analysis
465.48MB
Check
HS code mapping to non-tariff measures
176.33MB
Check
Aluminum products HS code insights
238.69MB
Check
Global trade intelligence newsletter
947.59MB
Check
Scan to install
Textile yarn HS code mapping to discover more
Netizen comments More
2857 Agriculture trade by HS code in Africa
2024-12-24 02:35 recommend
1821 Global trade credit risk analysis
2024-12-24 02:07 recommend
2907 European Union trade analytics
2024-12-24 01:21 recommend
2980 UK HS code duty optimization
2024-12-24 01:05 recommend
2240 HS code correlation with export refunds
2024-12-24 00:19 recommend