The reasons why the diesel car cannot catch fire: the engine compression is insufficient; the cylinder liner is seriously damaged; the piston is ring carbonated; the battery is not charged; the fuel tank is not oil or the pipeline is blocked; the air filter is too dusty or damp; the air intake is blocked, etc.
The reasons why the engine does not start are as follows: the battery is insufficient or out of power. For the diagnosis of such faults that the engine cannot start, the battery should be detected first. It must be clarified whether the battery is insufficient when the engine fails to start, and the battery needs to be charged. The engine start system fails.
The battery has insufficient power storage, so it can't drive the starter, so it can't catch fire.Problems with the fuel supply system, such as no oil in the fuel tank or the pipeline is not open, and the oil pump does not transfer oil, etc., which lead to the inability to ignite. Problems with the air intake system, such as air intake blockage, excessive dust accumulation in the air filter or moisture.
The reason why the diesel engine can't catch fire is that the engine oil line is not smooth, cylinder compression, lubricating oil and oil pump. The engine oil line is not smooth. Check whether the engine oil line is unobstructed. If you hear a squeaky sound from the fuel injector, it proves that the oil line is fine. Cylinder compression.
The reasons why diesel cars can't catch fire are: the oil line of the car engine is not smooth, the problem of cylinder compression and the problem of lubricating oil. If the diesel engine can't fire, it may be because the engine oil line is not smooth. It is necessary to check whether the engine oil line is smooth. If you hear a squeaky sound from the fuel injector, it means that the oil line is fine.
Oil pump.Check if there is air in the oil pump. If there is air in the oil pump, the diesel engine will not be ignited. Solution: If you have oil problems, you must go to a regular gas station to refuel. When you go out, you can bring a gauze bag to the muzzle of the refueling gun to filter impurities.
Fault analysis (1 ) There is air or moisture in the fuel system.If the oil pipe joint is loose or the oil inlet pipe is damaged by friction, the air will enter the fuel system. At the same time, diesel contains a certain amount of moisture. When there is more air and moisture, it will affect the normal start-up of the diesel engine.
The troubleshooting steps are as follows: 01 Close the throttle, reduce the pressure, and shake the handle to quickly rotate the flywheel. 02 Turn off the accelerator without decompression, shake the handle and slowly turn the flywheel. 03 Turn on the accelerator and decompress. 04 The hot car is ignited. The above steps can find the specific location of the fault, troubleshoot, and ensure the normal start of the diesel engine.
The ambient temperature is too low. When the temperature is low, the preheating of the diesel engine should be done well, otherwise it is not easy to start. The starting speed is low. For hand-cranked diesel engines, the speed should be gradually increased, and then the decompression handle should be pulled to the non-decompression position so that there is normal compression in the cylinder.
The electronic control system of each model is different, and the cause of the failure is also different. The fault diagnosis and exclusion should be combined with specific models and refer to relevant technical materials.
The reasons why the diesel generator set cannot be started: no fuel or insufficient fuel; the cooling water temperature of the engine cylinder is low; the battery voltage is low; the injection oil pump has air; starting motor failure; control loop failure.
Check whether the tools and materials are complete. Before disassembling the valve, we need to prepare the corresponding tools and materials, including wrenches, screwdrivers, cooling water, lubricants, detergents, etc. Remove the valve cover. First of all, we need to use a wrench to remove the screw on the valve cover, and then gently remove the valve cover.
First of all, open the video tutorial and you can see that a technician is adjusting the valve of the single-cylinder diesel engine. He first opened the hood of the engine, then removed the valve cover with a wrench, and then used a special tool to adjust the valve.
Its main function is to adjust the opening of the intake valve. Tightening this screw can reduce the opening of the intake valve, and loosening it can increase the opening. This is used to adjust the air-fuel ratio of diesel engines to achieve the best work efficiency and starting performance. Make sure that the intake valve is sealed.
Continue to screw into the nut on the top of the tie rod bolt to clamp the cylinder liner between the support plate and the pressure plate. Adjust the hook to make it located on the extension of the cylinder axis, hang it in the lock to hang the cylinder liner out and put it on the cushion. A single-cylinder diesel engine is a diesel engine with only one cylinder when classified according to the number of cylinders.
1. Then adjust it according to the working order of the engine 1342 or 1243. Use the process crankshaft to rotate 720. Double-row non-enter method.
2. The following is the relevant introduction: valve adjustment sequence and adjustment method: Take a 4-cylinder engine with a known ignition sequence of 1-3-4-2 as an example. First of all, put 1 cylinder on the compression stop to adjust its valve. Then rotate the crankshaft of the engine 180 degrees so that the 3 cylinders are in the stop adjustment gap under the intake.
3. Adjust it twice and rotate the crankshaft to the stop point on the 1 or 4th cylinder. Observe the convex handle of the camshaft of the 1 and 4 cylinders, and the convex handle of which cylinder is facing down (into the lower figure eight), then debug that cylinder. If it is in 1 cylinder, debug 1 row, 1 row, 2 rows, 3 rows.Then turn the crankshaft 360 degrees, and then debug 2 rows, 3 advances, 4 advances, 4 rows.
4. The following is a supplementary introduction to the valve gap adjustment method of the four-cylinder diesel engine: find the stop point of one-cylinder compression. According to the regulation of "double-row-no-in-in": double: that is, the intake and exhaust valves are adjusted;, no: that is, no. After adjustment, turn the crankshaft for a circle. Then press "No-Enter-Double-Row".
5. Next, let's explain in detail the diagram steps of the valve order of the diesel four-cylinder engine: First, we need to find the valve sequence diagram. The picture generally has stickers or labels on the hood or in the engine compartment, which can also be found in the vehicle maintenance manual.
Crank connecting rod mechanism The crank connecting rod mechanism is the main moving part of the engine to realize the working cycle and complete the energy conversion. It is composed of a fusele group, a piston connecting rod group and a crankshaft flywheel group.
Car engines, also known as car engines, mainly use gasoline engines and diesel engines; they are divided into four-stroke engines and two-stroke engines. According to the number of strokes required to complete a working cycle, they can be divided into four-stroke internal combustion engines and two-stroke internal combustion engines.
It can be said that it is the engine that created the car. The basic structure of the engine (as shown in the figure) is composed of main parts such as cylinder piston connecting rod crankshaft 4. Each cylinder has at least two valves, an intake valve (blue) and an exhaust valve (orange).
1. The reason why the diesel engine cannot start: check the power supply, check the oil supply, consider the possibility of insufficient air intake, consider whether the intake compression force is insufficient, consider whether the ambient temperature is too low, start the supporting output machinery with load, etc.
2. III: Plug-in open circuit or short circuit. The fuel injector harness, sensor harness, the whole vehicle harness plug-in is not plugged in or the harness is broken or short-circuited. Check the installation of the plug-in and check the connection of the line with a mimeter.
3. Circuit or electronic failure. The phenomenon of this failure is very sudden without any warning. The faults of the circuit include: fuse burnout, high-voltage coil breakage, low-voltage circuit breakage, central ignition wire falling off, split-fire head leakage, spark plug damage. Electronic failure mainly refers to the loss of function of the central computer control panel.
How to adapt to shifting trade policies-APP, download it now, new users will receive a novice gift pack.
The reasons why the diesel car cannot catch fire: the engine compression is insufficient; the cylinder liner is seriously damaged; the piston is ring carbonated; the battery is not charged; the fuel tank is not oil or the pipeline is blocked; the air filter is too dusty or damp; the air intake is blocked, etc.
The reasons why the engine does not start are as follows: the battery is insufficient or out of power. For the diagnosis of such faults that the engine cannot start, the battery should be detected first. It must be clarified whether the battery is insufficient when the engine fails to start, and the battery needs to be charged. The engine start system fails.
The battery has insufficient power storage, so it can't drive the starter, so it can't catch fire.Problems with the fuel supply system, such as no oil in the fuel tank or the pipeline is not open, and the oil pump does not transfer oil, etc., which lead to the inability to ignite. Problems with the air intake system, such as air intake blockage, excessive dust accumulation in the air filter or moisture.
The reason why the diesel engine can't catch fire is that the engine oil line is not smooth, cylinder compression, lubricating oil and oil pump. The engine oil line is not smooth. Check whether the engine oil line is unobstructed. If you hear a squeaky sound from the fuel injector, it proves that the oil line is fine. Cylinder compression.
The reasons why diesel cars can't catch fire are: the oil line of the car engine is not smooth, the problem of cylinder compression and the problem of lubricating oil. If the diesel engine can't fire, it may be because the engine oil line is not smooth. It is necessary to check whether the engine oil line is smooth. If you hear a squeaky sound from the fuel injector, it means that the oil line is fine.
Oil pump.Check if there is air in the oil pump. If there is air in the oil pump, the diesel engine will not be ignited. Solution: If you have oil problems, you must go to a regular gas station to refuel. When you go out, you can bring a gauze bag to the muzzle of the refueling gun to filter impurities.
Fault analysis (1 ) There is air or moisture in the fuel system.If the oil pipe joint is loose or the oil inlet pipe is damaged by friction, the air will enter the fuel system. At the same time, diesel contains a certain amount of moisture. When there is more air and moisture, it will affect the normal start-up of the diesel engine.
The troubleshooting steps are as follows: 01 Close the throttle, reduce the pressure, and shake the handle to quickly rotate the flywheel. 02 Turn off the accelerator without decompression, shake the handle and slowly turn the flywheel. 03 Turn on the accelerator and decompress. 04 The hot car is ignited. The above steps can find the specific location of the fault, troubleshoot, and ensure the normal start of the diesel engine.
The ambient temperature is too low. When the temperature is low, the preheating of the diesel engine should be done well, otherwise it is not easy to start. The starting speed is low. For hand-cranked diesel engines, the speed should be gradually increased, and then the decompression handle should be pulled to the non-decompression position so that there is normal compression in the cylinder.
The electronic control system of each model is different, and the cause of the failure is also different. The fault diagnosis and exclusion should be combined with specific models and refer to relevant technical materials.
The reasons why the diesel generator set cannot be started: no fuel or insufficient fuel; the cooling water temperature of the engine cylinder is low; the battery voltage is low; the injection oil pump has air; starting motor failure; control loop failure.
Check whether the tools and materials are complete. Before disassembling the valve, we need to prepare the corresponding tools and materials, including wrenches, screwdrivers, cooling water, lubricants, detergents, etc. Remove the valve cover. First of all, we need to use a wrench to remove the screw on the valve cover, and then gently remove the valve cover.
First of all, open the video tutorial and you can see that a technician is adjusting the valve of the single-cylinder diesel engine. He first opened the hood of the engine, then removed the valve cover with a wrench, and then used a special tool to adjust the valve.
Its main function is to adjust the opening of the intake valve. Tightening this screw can reduce the opening of the intake valve, and loosening it can increase the opening. This is used to adjust the air-fuel ratio of diesel engines to achieve the best work efficiency and starting performance. Make sure that the intake valve is sealed.
Continue to screw into the nut on the top of the tie rod bolt to clamp the cylinder liner between the support plate and the pressure plate. Adjust the hook to make it located on the extension of the cylinder axis, hang it in the lock to hang the cylinder liner out and put it on the cushion. A single-cylinder diesel engine is a diesel engine with only one cylinder when classified according to the number of cylinders.
1. Then adjust it according to the working order of the engine 1342 or 1243. Use the process crankshaft to rotate 720. Double-row non-enter method.
2. The following is the relevant introduction: valve adjustment sequence and adjustment method: Take a 4-cylinder engine with a known ignition sequence of 1-3-4-2 as an example. First of all, put 1 cylinder on the compression stop to adjust its valve. Then rotate the crankshaft of the engine 180 degrees so that the 3 cylinders are in the stop adjustment gap under the intake.
3. Adjust it twice and rotate the crankshaft to the stop point on the 1 or 4th cylinder. Observe the convex handle of the camshaft of the 1 and 4 cylinders, and the convex handle of which cylinder is facing down (into the lower figure eight), then debug that cylinder. If it is in 1 cylinder, debug 1 row, 1 row, 2 rows, 3 rows.Then turn the crankshaft 360 degrees, and then debug 2 rows, 3 advances, 4 advances, 4 rows.
4. The following is a supplementary introduction to the valve gap adjustment method of the four-cylinder diesel engine: find the stop point of one-cylinder compression. According to the regulation of "double-row-no-in-in": double: that is, the intake and exhaust valves are adjusted;, no: that is, no. After adjustment, turn the crankshaft for a circle. Then press "No-Enter-Double-Row".
5. Next, let's explain in detail the diagram steps of the valve order of the diesel four-cylinder engine: First, we need to find the valve sequence diagram. The picture generally has stickers or labels on the hood or in the engine compartment, which can also be found in the vehicle maintenance manual.
Crank connecting rod mechanism The crank connecting rod mechanism is the main moving part of the engine to realize the working cycle and complete the energy conversion. It is composed of a fusele group, a piston connecting rod group and a crankshaft flywheel group.
Car engines, also known as car engines, mainly use gasoline engines and diesel engines; they are divided into four-stroke engines and two-stroke engines. According to the number of strokes required to complete a working cycle, they can be divided into four-stroke internal combustion engines and two-stroke internal combustion engines.
It can be said that it is the engine that created the car. The basic structure of the engine (as shown in the figure) is composed of main parts such as cylinder piston connecting rod crankshaft 4. Each cylinder has at least two valves, an intake valve (blue) and an exhaust valve (orange).
1. The reason why the diesel engine cannot start: check the power supply, check the oil supply, consider the possibility of insufficient air intake, consider whether the intake compression force is insufficient, consider whether the ambient temperature is too low, start the supporting output machinery with load, etc.
2. III: Plug-in open circuit or short circuit. The fuel injector harness, sensor harness, the whole vehicle harness plug-in is not plugged in or the harness is broken or short-circuited. Check the installation of the plug-in and check the connection of the line with a mimeter.
3. Circuit or electronic failure. The phenomenon of this failure is very sudden without any warning. The faults of the circuit include: fuse burnout, high-voltage coil breakage, low-voltage circuit breakage, central ignition wire falling off, split-fire head leakage, spark plug damage. Electronic failure mainly refers to the loss of function of the central computer control panel.
Value-added exports by HS code
author: 2024-12-23 22:41Wool and yarn HS code verification
author: 2024-12-23 22:38Customs duty optimization strategies
author: 2024-12-23 21:29Predictive analytics for trade flows
author: 2024-12-23 21:21HS code-driven route-to-market planning
author: 2024-12-23 20:06Global trade reporting frameworks
author: 2024-12-23 21:38Canned foods HS code classification
author: 2024-12-23 21:37HS code-based inbound logistics optimization
author: 2024-12-23 20:31How to interpret trade volume changes
author: 2024-12-23 20:09Real-time customs processing times
author: 2024-12-23 20:02
Apparel import export statistics
862.43MB
Check
How to simplify multi-leg shipments
664.11MB
Check
HS code guides for automotive parts
456.41MB
Check
shipment data access
575.52MB
Check
How to ensure trade compliance audits
464.28MB
Check
Sourcing intelligence from customs data
217.49MB
Check
Global trade partner compliance checks
288.23MB
Check
Inland freight HS code applicability
919.93MB
Check
International trade knowledge base
288.73MB
Check
European Union trade analytics
934.65MB
Check
Agriculture import export insights
563.56MB
Check
HS code-based vendor qualification
874.75MB
Check
Timber (HS code ) import patterns
416.68MB
Check
How to align trade data with demand planning
688.47MB
Check
Trade data for industrial raw materials
494.11MB
Check
Trade data for energy sector
822.64MB
Check
HS code-based risk profiling for exporters
823.82MB
Check
How to access restricted trade data
243.44MB
Check
How to find HS code data for specific countries
648.25MB
Check
HS code mapping for re-importation
997.85MB
Check
Advanced commodity classification analytics
323.38MB
Check
Trade data solutions for freight forwarders
311.33MB
Check
Real-time HS code duty updates
392.14MB
Check
HS code-based compliance checks for EU
679.35MB
Check
Trade data-driven credit insurance
714.48MB
Check
HS code-driven risk mitigation
657.87MB
Check
Industrial equipment HS code alignment
224.72MB
Check
HS code-driven supply chain benchmarking
467.73MB
Check
Medical diagnostics HS code classification
837.17MB
Check
Pharmaceutical raw materials HS code checks
619.98MB
Check
How to leverage analytics in procurement
494.64MB
Check
Refined sugar HS code identification
148.51MB
Check
Pharma finished goods HS code references
832.18MB
Check
HS code-driven cross-border e-commerce
892.91MB
Check
APAC special tariff HS code listings
239.87MB
Check
How to identify export-ready products
226.36MB
Check
Scan to install
How to adapt to shifting trade policies to discover more
Netizen comments More
1449 Country-specific HS code duty reclaims
2024-12-23 22:28 recommend
798 Global trade data storytelling
2024-12-23 22:04 recommend
756 How to refine supply chain visibility
2024-12-23 21:10 recommend
1908 HS code lookup for Asia-Pacific markets
2024-12-23 20:48 recommend
969 HS code reference for mineral exports
2024-12-23 20:46 recommend