Hello, reading the fault code 1215, which means that the air flow meter or its line is poor. After testing, the impedance of the air flowmeter does not meet the requirements. After replacing the air flowmeter, the condition of the car improved slightly, but the fault was still there. Check again and find that the 4th cylinder spark plug is covered with gasoline, indicating that the cylinder is not working.
The engine has serious carbon accumulation. The most common cause of idling jitter is excessive carbonisation of the throttle valve or fuel nozzle.
The solutions to unstable idle speed, shaking, shaking and black smoke are as follows: the engine is seriously carbonized. The common cause of car shaking is that the throttle valve is too dirty or the fuel nozzle has too much carbon.Solution: Clean the oil road and check whether there is carbon in the idle motor, which should be cleaned.
The control unit receives the wrong signal and sends the wrong instruction, causing the engine idling intake control to be inaccurate, causing the engine to burn abnormally, which is an indirect cause of unstable idle speed. Common causes are: air flow meter or its line failure; intake pressure sensor or its line failure; engine control unit plug due to poor contact with water inlet or internal computer failure.
Engine ignition order is 2; that is to say, when cylinder 1 is doing work, cylinder 3 is in a compressed state, cylinder 4 is in the intake state, and cylinder 2 is in the exhaust state. Status.
People sit in the cab, and the order of the cylinder is: 5 on the right, and 6 on the left.In this case, the ignition order is: 1-4-5-2-3-6.
The ignition order of the engine is 2; that is, when the 1st cylinder is in the "work", the 3rd cylinder is in the "compression" state, the 4th cylinder is in the "ink-ink" state, and the 2nd cylinder is in the "exhaust" state. Depending on the number of engine cylinders, the ignition order of the engine will also vary.
Engine carbon accumulation problem, the engine will accumulate some carbon accumulation after a period of use, which will cause engine damage, difficulty in starting, poor acceleration, starting The machine is too noisy and other phenomena. Mixed gas combustion is poor and gas combustion is insufficient. Sensor problem. Multiple sensors are aging. If the owner does not add oil as required, it will lead to accelerated engine wear and abnormal operation in the long run, and the engine fault light will turn on. Generally, replacing the oil with the corresponding conditions can eliminate the fault light. The reasons why the engine fault light is on are engine carbonisation problems, poor combustion of mixed gas, sensor problems, maintenance problems and oil quality problems.Car owners need to regularly clean the carbon accumulation of the engine, check the working condition of the sensor, maintain it regularly, and use qualified oil products. The fuel quality is poor and does not meet the standard.
How to integrate trade data with RPA-APP, download it now, new users will receive a novice gift pack.
Hello, reading the fault code 1215, which means that the air flow meter or its line is poor. After testing, the impedance of the air flowmeter does not meet the requirements. After replacing the air flowmeter, the condition of the car improved slightly, but the fault was still there. Check again and find that the 4th cylinder spark plug is covered with gasoline, indicating that the cylinder is not working.
The engine has serious carbon accumulation. The most common cause of idling jitter is excessive carbonisation of the throttle valve or fuel nozzle.
The solutions to unstable idle speed, shaking, shaking and black smoke are as follows: the engine is seriously carbonized. The common cause of car shaking is that the throttle valve is too dirty or the fuel nozzle has too much carbon.Solution: Clean the oil road and check whether there is carbon in the idle motor, which should be cleaned.
The control unit receives the wrong signal and sends the wrong instruction, causing the engine idling intake control to be inaccurate, causing the engine to burn abnormally, which is an indirect cause of unstable idle speed. Common causes are: air flow meter or its line failure; intake pressure sensor or its line failure; engine control unit plug due to poor contact with water inlet or internal computer failure.
Engine ignition order is 2; that is to say, when cylinder 1 is doing work, cylinder 3 is in a compressed state, cylinder 4 is in the intake state, and cylinder 2 is in the exhaust state. Status.
People sit in the cab, and the order of the cylinder is: 5 on the right, and 6 on the left.In this case, the ignition order is: 1-4-5-2-3-6.
The ignition order of the engine is 2; that is, when the 1st cylinder is in the "work", the 3rd cylinder is in the "compression" state, the 4th cylinder is in the "ink-ink" state, and the 2nd cylinder is in the "exhaust" state. Depending on the number of engine cylinders, the ignition order of the engine will also vary.
Engine carbon accumulation problem, the engine will accumulate some carbon accumulation after a period of use, which will cause engine damage, difficulty in starting, poor acceleration, starting The machine is too noisy and other phenomena. Mixed gas combustion is poor and gas combustion is insufficient. Sensor problem. Multiple sensors are aging. If the owner does not add oil as required, it will lead to accelerated engine wear and abnormal operation in the long run, and the engine fault light will turn on. Generally, replacing the oil with the corresponding conditions can eliminate the fault light. The reasons why the engine fault light is on are engine carbonisation problems, poor combustion of mixed gas, sensor problems, maintenance problems and oil quality problems.Car owners need to regularly clean the carbon accumulation of the engine, check the working condition of the sensor, maintain it regularly, and use qualified oil products. The fuel quality is poor and does not meet the standard.
Comparative freight cost modeling
author: 2024-12-23 21:44Global tariff databases by HS code
author: 2024-12-23 20:20Trade data integration with CRM
author: 2024-12-23 20:15Heavy machinery parts HS code verification
author: 2024-12-23 20:12Global trade intelligence benchmarks
author: 2024-12-23 20:11HS code adaptation for local regulations
author: 2024-12-23 22:33Trade data integration with ERP systems
author: 2024-12-23 22:17Export data analysis for consumer goods
author: 2024-12-23 20:58Food additives HS code classification
author: 2024-12-23 20:39471.75MB
Check613.59MB
Check594.11MB
Check149.26MB
Check246.63MB
Check189.39MB
Check111.68MB
Check138.58MB
Check456.29MB
Check817.11MB
Check668.85MB
Check988.83MB
Check889.46MB
Check631.86MB
Check965.96MB
Check626.74MB
Check177.46MB
Check499.95MB
Check191.92MB
Check362.69MB
Check828.97MB
Check225.92MB
Check313.95MB
Check694.54MB
Check478.95MB
Check586.68MB
Check911.57MB
Check885.73MB
Check799.38MB
Check344.53MB
Check575.18MB
Check111.31MB
Check627.51MB
Check927.73MB
Check255.43MB
Check966.91MB
CheckScan to install
How to integrate trade data with RPA to discover more
Netizen comments More
2518 GCC countries HS code tariffs
2024-12-23 22:39 recommend
898 HS code classification for electronics
2024-12-23 22:30 recommend
1545 HS code automotive parts mapping
2024-12-23 22:14 recommend
153 Trade finance structuring by HS code
2024-12-23 21:36 recommend
914 Premium trade data intelligence subscriptions
2024-12-23 21:04 recommend